3,200 PSI Max Relief Pressure Makes the 12 Volt DC Hydraulic Power Unit a Heavy Lift Leader

This VEVOR 12 volt DC hydraulic power unit has a maximum relief pressure of 3,200 psi and a working pressure range of 16 to 20 MPa. It provides the steady hydraulic force that tough lift jobs need. The pressure output stays steady even when the load changes, whether it's powering a loaded dump trailer or raising a scissor lift to its full height. It doesn't drop or surge unexpectedly.

The built-in relief valve automatically opens when the system pressure exceeds safe levels, relieving excess pressure before downstream components can be damaged. This passive protection operates continuously without operator input. It protects cylinders, hoses, and seals over thousands of duty cycles and greatly increases the overall service life of the hydraulic system it is connected to.

DC 12V, 1.6 kW Motor Powers Unit Instantly On Demand

This pump can connect directly to vehicle batteries, trailer wiring harnesses, and portable power banks without needing any extra electrical hardware or voltage converters. It uses 1.6 kW from a standard 12-volt DC source. The motor reaches its full operating speed in just a few seconds after being turned on, so it can provide hydraulic pressure right away when needed.

This 12 volt architecture is ideal for many mobile applications. Dump trailers, liftgates, and bucket conveyors that are far from grid power all use the same 12V source already in the towing vehicle. It means there is no need for additional wiring runs, and the entire electrical installation is simplified to just two clearly labeled power leads.

0.91 GPM Flow Rate Gives the Unit Precise Cycle Control

The cylinder extension moves at a controlled, moderate speed of 0.91 gallons per minute, which meets the needs of precision lift applications. Scissor lifts, lift tables, and car-lifting platforms all need to move smoothly and predictably, not with sudden jerks. This pump's volumetric output gives them the controlled performance they need when it's full.

A steady flow also helps keep cycle times consistent across a wide range of loads. Operators can confidently plan raise and lower sequences because they know the pump will operate the same way, regardless of load weight, as long as the load is within the maximum rated capacity of the connected hydraulic cylinder.

13-Quart Rust-Resistant Steel Reservoir Keeps the Hydraulic Power Unit Running Cool

The 13-quart steel reservoir can hold enough fluid to effectively absorb and spread heat during long duty cycles, keeping the oil temperature and viscosity within the best operating range. Compared to compact tanks, tanks with greater fluid capacity slow the temperature rise significantly. It reduces the risk of seal degradation and fluid breakdown, which can shorten pump lifespans in high-frequency applications.

The tank is made of rust-resistant steel, not a polymer. It can withstand daily impacts, vibration, moisture, and UV exposure common on active job sites and in open truck beds. The hard-metal shell resists denting, cracking, and warping under heavy use. It keeps the reservoir completely sealed, preventing air and dirt from entering the hydraulic fluid.

Single Acting Design Simplifies the Valve System

In a single-acting operation, the cylinder only moves when the load is heavy enough, and the piston is pulled back by gravity. This simple method eliminates the extra valve circuitry, hydraulic ports, and connection points that double-acting systems require. It makes the installation cleaner and faster, with fewer points for leaks throughout the circuit.

Gravity-return lowering is also a useful safety feature in dump trailer applications. If the power goes out in the middle of a cycle, the trailer bed will lower as expected under manual valve control, rather than remaining suspended under pressure indefinitely. It gives operators a safe, controllable way to reach a resting position even if power goes out unexpectedly in remote areas.

Pre-Assembled Construction Reduces Installation Time Sharply

VEVOR sends this 12 volt DC hydraulic power unit fully put together, with the motor, pump body, 13-quart reservoir, control valve, and relief mechanism all in one package that can be bolted on. The installation is completed by adding hydraulic oil, connecting the two power leads, and attaching the hydraulic hoses. Many operators can do this in less than 30 minutes without any special hydraulic tools or professional help.

Every hydraulic connection has SAE #6 port fittings that fit the most common standard hose ends sold at industrial supply and farm equipment stores across the country. This compatibility means that you don't have to look for custom adapters in almost all installation situations. It speeds up setup and ensures that every hydraulic connection remains leak-free at the pump's full-rated operating pressure from day one.

Multi Application Versatility Makes This 12 Volt DC Hydraulic Power Unit Shop Ready

This pump is a great investment for contractors, fabricators, and fleet maintenance shops because it can power dump trailers, liftgates, scissor lifts, lift tables, small shop presses, or bucket conveyors as needed. To switch between machines, typically all you have to do is reconnect the hydraulic hoses. It lets one unit work on several machines at different job sites during the week.

The small, space-efficient footprint fits mounting spots in tight under-frame trailer spots and narrow truck-bed compartments where bigger power units won't fit. Even though it is small, the 12 volt DC hydraulic power unit can provide output comparable to that of some larger, more expensive industrial pumps. It makes professional-grade hydraulic capability available to both independent operators and small shops.