Reseñas de clientes para Lijadora de banda VEVOR de 1500 W y 2 HP, 5 x 208 cm, velocidad variable, para metalurgia, pulidora de banda 3 en 1 con 3 moldes de pulido y soporte de herramientas de placa plana para la fabricación de cuchillos.

Very smooth and stable. Seems to be a really nice machine. Absolutely a great price compared to others I have seen. Just wish I had instructions in English for the controller. 100% Chinese language. Don’t know how to adjust speed, etc.

Very nice belt sander. Cut 1 1/2 inch off the end of the tool holder bar and then 2x72 belts worked fine.

how is the "concave" attachment installed? No information provided with machine. Otherwise machine is very nice to use.

I have had this machine a week and so far I have been unable to use it because the thing is total garbage. The belt wont track no matter what I do to adjust anything and everything. the square tube that the other piece goes into looks like discarded remnants and the accesory just flops around in the hole. Funny, I dont see the same issue with the free machines being sent to youtubers. the tracking wheel has a ton of problems. The adjustment wheel is not sitting straight. I have done everything to try and fix that issue, and it is still sitting at a tilted cant. The needle bearings riding on cheap washers are already digging into the washers because needle bearings should not be riding on simple washers. I had to machine some stainless washer/bushings to address that. The plate that holds the adjustment wheel doesn't fully support the washers/bushings. the sleeve pin looks like it was rough ground by hand and the base of that pin needed trued up int he lathe, and its free floating, not sure why but that pin should be pressed into the plate and welded secure so the adjustment wheel rides on that pin instead of relying on clamping pressure to force the adjustment wheel straight. I tried adjusting the motor, and no luck there either, the motor is sitting all way at the end of its adjustment travel. THAT ALONE SHOULD BE A RED FLAG. I have gone over everything and the belt will not track properly and sticks off the front rollers. This means I cant grind on that, if I make the adjustment so the belt is centered on the front wheels, the belt is then overhanging on the adjustment wheel and thats still a problem because one, that's not how that should be and 2, that overhand will cause the belts on it to come undone and destroy themselves. And I have invested in 3 very expensive belts and Im not going to let those belts be ruined because vevor is scamming the public on trash machines. The base has an elongated curve in it so it doesn't sit flat on the table, and it rocks back and forth. I had to put a heavy bar mat under it to take up that bend so it would not rock back and forth. WHERE IS THE ON AND OFF SWITCH? Previous belt grinders had them. The VFD has no protection from grinding dust entering it and gosh, I wonder what issues will result from that. I had to buy an expensive 30 amp on and off switch so I could turn this machine on and off. The large wheel that came with this has deep nicks in the wheel. Since when is it ok to send stuff like this to customers? Vevor needs to be held accountable at a much higher level than just their corporate complaint dept. This nonsense is dishonest and needs to stop. I made a full review video posted on Opies Home Shop on YT for all to see and its not a good review oh vevor! https://www.youtube.com/watch?v=hh30YucXXJE

The VFD failed after 2 1/5 months and VEVOR IS NO HELP! DO NOT BUY ANY MAJOR PIECE OF EQUIPMENT FROM VEVOR! They do not stand behind their products! This is the second VFD failure on one of their grinder/sanders I have experienced. I should have learned my lesson with the 1x30 sander that failed but I took a chance on their 2x72 and now I have $1000 of machine that does not work and VEVOR refuses to replace or refund! EXTREMELY POOR BUSINESS PRACTICES! I will continue to tell everyone I know to avoid this company at all costs!