Reseñas de clientes para Caja de acero VEVOR NEMA, dimensiones 16 x 12 x 8 pulgadas, caja eléctrica de acero NEMA 4X, clasificación IP66 de resistencia al agua y al polvo, adecuada para uso en exteriores e interiores, incluye placa de montaje.

So gut verarbeitet nur die wand Befestigungen sollte in einer Dichten Ausführung sein

The box is well built and it's really a good design. I really like the cooling fan and the ventilation. However, there are a few flaws to this design. First of all, if this is an outdoor enclosure, it should be bug proof 100%. Yes, there is mesh for the side vents on the inside of the enclosure, but then there is a big gaping hole at the bottom of each vent for flies and other bugs to go live in there. Over time bugs going in there to live and make nests and all that we'll plug up the mesh screen. So there should be a mesh screen at the bottom of each vent where the big gaping hole is for air to flow through as well as one on the inside of the enclosure. And same with at the top where the fan vents out. There's little slotted holes for the air to go out of the enclosure from the fan. And there is a mesh screen between the fan and this little opening where the air blows into. But again flies and all kinds of other little bugs are going to go live inside of there. So where the little slotted holes are there needs to be a mesh screen covering that as well. So no bugs can go live anywhere in this enclosure. Also there are pre-drilled holes for mounting hardware. There's two at the top of the enclosure and two at the bottom. The metal insert that comes with the enclosure is too close to the bottom holes for the supplied nuts and bolts that come with this kit. The nuts that come with it are huge and the holes on the bottom are too close to the insert for these knots to even have space to spin and tighten on. Let alone get a socket bit on there. The top holes are okay. I was able to get the socket on there. But I had to use smaller nuts and bolts for the bottom holes. It would just make sense if the

Prima kast, goede kwaliteit en afwerking. Prijs ok.

Il est impossible de pouvoir télécharger la facture.

La réalisation du boîtier semble être de très bonne qualité. Le joint est ferme, ce qui laisse présager une parfaite herméticité de l'ouverture du boîtier. Il y a cependant quelques points de vigilance à retenir : - Les trous ne sont obstrués que par des capuchons en plastique blanc. Si les 4 au dos du boîtier seront obligatoirement ôtés pour le fixer à un support, et les trous comblés par la vis qui va traverser chacun d'entre eux, ainsi que l'écrou intégrant un joint caoutchouc placé à l'intérieur du boîtier, les 2 sur la face avant permettant d'inverser la position des charnières restent obstrués par ces mêmes capuchons en plastique de façon permanente, uniquement emboîtés dans le trou. Il n'assurent aucune étanchéité et l'écart entre la porte et leur emplacement est suffisamment grand pour laisser passer l'eau, même par simple ruissellement. Il faudrait utiliser ce boîtier annoncé IP65 dans un endroit protégé pour assurer l'absence d'infiltration d'eau, ce qui est plutôt illogique. - L'ouverture du bas sur laquelle se fixe la plaque à usiner, pour placer des presse-étoupes par exemple, est légèrement surélevée par rapport au bas du boîtier. J'imagine que cela permet d'éviter l'infiltration d'eau par capillarité, mais cela créé également un petit volume à l'intérieur du boîtier en bas dans lequel l'eau qui s'est infiltrée peut stagner et aboutir à un fort taux d'humidité fatal pour les équipements qu'il renferme. Un petit trou d'évacuation de cette eau est à envisager, même pour évacuer uniquement la condensation causée par la différence de température entre l'extérieur et l'intérieur du boîtier. - La plaque fournie pour fixer les éléments qui seront intégrés dans le boîtier ne permet pas de bénéficier de toute la surface disponible à l'intérieur. J'ai redécoupé une plaque alu un peu plus large qui s'insère également sans problème dans le boîtier. En résumé, je ne suis pas très confiant quand au sort de l'électronique (nœuds LoRa et Meshtastic) que je vais intégrer dans ce boîtier, qui sera fixé en pied de mat d'antenne TV, en bordure de toiture, face aux vents dominants. J'espérais obtenir quelque chose de plus durable et tout aussi efficace qu'un boîtier Plexo...

Overall I’m happy with it. I’m glad I went with the 20” height. I was going to to the 16” initially as my EA Charger is spec’d a bit below that. However I honestly doubt I would have been able to make anything less than this height work. I just needed that room to work and secure the nuts. I did have to modify it a bit. I took a circular hole drill-bit to cut a half circle into the bottom rectangular opening. I did this to get the plug and cord through. I decided this much easier than opening up my charger and disconnecting everything to pull the plugs out that way. Then I would have had to reconnect it all while in the box…. No thx. Anyways all said and done, I’m very happy with it. I love the look and everything. The only down vote I give that prevented it from getting a 5 star review is the lock that comes with this box…. The “key” is a joke. No key is really even needed. You can turn this lock with almost anything small and flat. I used a car key to see if it would open it. A flathead screwdriver would work…. So I don’t think this qualifies by any stretch of the imagination to be called a Lock. So now I’m looking on Amazon for a Cam Lock. However I’m hoping Vevor Customer Service can team me the exact size. I asked under “Questions & Answers” but they responded basically saying to replace the guts of the lock with a key’d part…. That sends like much more with then ordering a whole new Cam Lock…. Anyways. That is my only real complaint. Other than that I love it. It feels really sturdy and seems to be really well made and of high qualify. I didn’t love the price… but you know, You Gotta Pay To Play. I’ll attach some pics. It’s not done. The plug situation is a mess. The Electrify American plug to the wall is beyond short. So I’m going to have to move some things around to make it all hang pretty. Will post updated pics soon.

After looking for a good deal I settled on this Vevor nema box. It has plenty of room to house all of the electrical components required in my latest build.

Is built well and was easy to put into service

Worked perfectly for what I needed

Muito bom material