Reseñas de clientes para Cizalla de guillotina VEVOR, cizalla manual de 30 cm para chapa metálica, herramienta resistente para cortar placas de metal, con marco de acero sólido, alta precisión, para cortar placas PCB, aluminio, acero, cobre y plástico.

Werkzeug im Auslieferungszustand nicht brauchbar! Bei der gelieferten Blechschere besteht das gleiche Problem wie bei Kevin. Amboss und Schneidrad überlappen und können nicht so eingestellt werden, dass sie leicht saugend parallel zueinander laufen. Der Halter ist einfach zu schmal. So ist diese Schere nicht brauchbar und auch den reduzierten Preis nicht wert! Laut Beschreibung soll sie bei Lieferung optimal eingestellt sein. Das sah dann so aus, dass das Schneidrad so verkantet und verspannt eingebaut war, dass sich das Schneidrad gar nicht drehen konnte. Das sollte doch jedem Mitarbeiter des Herstellers auf den ersten Blick auffallen. Gibt es eine Qualitätssicherung beim Hersteller? Schade Wenn Sie sich an den Support richten, landen Sie bei einer Ki, die immer freundliche Mails generiert, aber Ihnen nicht weiterhilft, aber stets Bilder anfordert, auch wenn Sie schon mehrfach geschickt wurden .

Pessimo articolo, sicuramente dal prezzo cosi contenuto l avrei dovuto capire fin da subito, tuttavia avevo necessità di una taglierina e questa era l unica disponibile in pochi giorni. E' praticamente inutilizzabile, oltre ad essere vecchia, si percepisce dallo stato di usura della vernice che sia stata prodotta qualche anno fa e conservata male in deposito. Presenta un errore tecnico che è rappresentato da uno "scalino", che rende impossibile un taglio non sbeccato. Non trovo quale altro utilizzo se ne possa fare, di certo non taglia fogli di allumino neanche di 4/10 di spessore (poco più di un foglio di carta. Sconsigliatissimo

Tried to cut a 1,5 mm steel plate, but a shear pin inside broke iand it is now unusable. But it was good for cutting aluminum plates and easy to cut round shapes. Have tried to replace the shear pin with a piece of a drillbit, but the material is a bit warped and I will have to use an angle grinder to remove it, but I think it will be possible to use it again. Will only use it for Aluminium in the future since the steel is to soft for proper operation when cutting steel

Product never arrived. Lost in transit.

Esto es una estafa he pedido. La maquina. Dos ves la primera se perdió he esperado mas de 15 días para la otra Me he puesto en contanto con varios agentes y ninguno ha podido dar una explicación La ultima agente sr elena me trato como sin importancia despidiéndose con que me lo reembolsa y ya sin darme una solución adiós y fuera Soy un cliente de vevor y siempre con mis compañeros de trabajo he hecho publicidad de una empresa seria donde comprar ahora no entiendo que ha pasado

Esto no corta patina el engranaje quisiera devolverlo por k no vale pa na

The description says it will cut steel to .08 (80 thousandths) thick, which is 14 gauge steel. I am using a lot of 16ga HOT ROLLED steel, and it will not cut it. I have had to resort to using a plasma cutter or friction blade and trimming/finishing. To see what it would cut, I cut some 20gauge aluminum sheet just fine, as well as some 20gauge hot rolled steel. Even cold-rolled steel at 18 gauge would not cut. So, since I bought this to do 16 gauge steel, its a big disappointment. But I do a lot of circuit board work and it cuts FR4 easily so I'll keep it for that. One reviewer says he uses it to cut 12Gauge steel, I dont see how.

Don't buy. Price was tempting. i just got around to using it. See the pics. Anvil and blade don't line up. This thing wouldn't cut cardboard. Either the anvil or the blade will have to be ground down to work. I'm surprised there wasn't any shims to add or subtract. I would expect it to at least work once before I have to fix/modify it.

I am afraid to say this is not very good quality used it first time and broke not very robust and engeeniring is of a low quality so not good

Does not want to cut sheet metal it slips a lot