Reseñas de clientes para VEVOR Horquilla para paletas con enganche de 3 puntos de 2000 libras, accesorio de horquilla para tractor de categoría 1, 25.5\'\'x22\'\'x41\'\', accesorio de acero para equipo pesado de tractor, para

Ce lève-palettes est très efficace et me convient parfaitement. Toutefois, j’ai relevé deux points à améliorer : 1. L’écartement des lames est trop large, ce qui oblige à prendre les palettes par le grand côté et empêche de les saisir normalement. 2. Les tiges en fer servant à l’accroche présentent beaucoup de jeu, car elles ne s’insèrent que dans un seul trou. Il serait préférable d’ajouter une deuxième plaque, décalée de quelques centimètres, afin de pouvoir insérer les tiges dans les deux plaques et ainsi éliminer ce jeu

Im Vergleich zur Konkurrenz ist das Teil echt preiswert. Es ist auf jeden Fall nicht billig obwohl es den Anschein hat nicht in Deutschland produziert worden zu sein. Die Ausnahme für den Dreipunkt ist aus massivem Stahl gefertigt. Jedoch wurde bei der Aufnahme für die beiden Kufen doch etwas geschlampt. Die Toleranzen sind zu hoch und dadurch hat das ganze Fuhrwerk zu viel Spiel. Hoffe dass dadurch nicht die Tragfähigkeit leidet. Mit ein paar Unterlegscheiben läßt sich das Problem jedoch in den Griff kriegen. Ansonsten keine Auffälligkeiten. Sogar alle Bolzen mit Sicherungssplint sind mit dabei. Also für den Preis echt ok.

I purchased these 6 weeks ago. They arrived very quickly. The box was damaged. It looked like somebody taped part of a box over the original box. The parts bag was empty. It looked like somebody took the hardware out for a different set that was missing hardware and patched the box. It was missing all of the hardware to clamp to the bucket. Useless without it. I contacted customer support at least a dozen times. I get the run around. Parts are shipped. Parts are delayed. Please be patient. Here is a $15 credit. How about a $30 credit. I declined the credits as the forks are useless without the hardware, and I can't find the hardware that fits properly at the store. I have asked for a return several times, and keep getting different resolution options without getting me the hardware needed. I have asked that they take the hardware out of another box so that I can use the forks. Still no resolution. Frustrating.

Its hard to keep them for moving back and forth you can’t tighten them enough t on keep them from sliding under pressure

The bolt down clamps are way too cheap made. If you have a decent cutting edge on your machines bucket, it won’t clamp down enough

They ok not to good on your bucket..

I purchased these forks to lift pallets and other things on my Massey Ferg 1742 tractor. They work OK, but it is an absolute pain to get them attached and oriented properly, and despite my best efforts and strength, they will still shift under heavy loads. They are definitely built with solid metal, though the welds are not stellar. They weigh a lot, so be aware 1) when the package comes and 2) when you are fitting them. I absolutely HATE the 90 degree, 4 inch long arms on the top of the tightening bolts, because you sure as heck are not hand-tightening if you think you will keep the forks secure/in-place. After hand tightening, I have to use an open end wrench on the 90-degree and then a 1 1/4" open end to tighten the adjustment nut on the bottom before it has any chance of not moving (but it still will). Also, the stabilizer bar that goes between the forks is helpful, but when moving pallets it has to be all the way back to the stops, near the bucket, so it is only moderately useful. Overall, I am satisfied with the performance based on the cost, but don't kid yourselves (or watch the paid youtube reviews that make it look as smooth as silk), these forks are a challenge taking on/off and are not anywhere near as stable as a dedicated fork attachment.

Forks are definitely heavy duty, can be kind of tough to tighten and the stabilizer bar that came with it is useless due to the wing nut being stripped upon its arrival to me, tried to get it out and could not budge it. The head of the wing but just ended up spinning, welded it together again and tried again, got it out 1/4 turn and it broke the weld.. have not tried to contact vevor about it as I have a feeling nothing will get done.

È arrivato incompleto senza forche

Les fourches ne font pas la même dimension