Reseñas de clientes para Máquina de corte de cuero VEVOR, troqueladora manual con placa de repujado de 11 x 5,5 pulgadas, troqueladora con doble eje guía y carrera de presión de 0,47 pulgadas, máquina de repujado de cuero para diversos materiales.

Great machine, wish it wasn't so expensive but everything quality is expensive. Only two issues. The locking pins for the rollers were loose in the package and I almost through one out as I found it on the floor before assembling the machine. The plastic bag had several holes it it so they were loose and I didn't recognize it before fully unpackaging it. I would recommend the manufacturer tape them in place or in it's own small bag. The "assembly instructions" are not assembly instructions and are just a small useless list of don'ts. I love it and it is working great!

Funciona perfecta mente, Muyy útil para cortar cuero o cartón donde se requieren muchos cortes iguales venden los moldes en muchas weps

presse de confection lourde de très bonne confection. Elle sent la qualité de fabrication. Facile d'utilisation, une fois la presse réglée il est facile de faire des découpes en cuir.

Really satisfied, works perfectly. Well packaged in small crate. Easy to adjust and align. Proper spacing for embossing and cutting dies makes it very easy to use, almost effortless. Thank You people at Vevor for a great product. Highly recommend ⭐⭐⭐⭐⭐

Goed material

Completely solid product. Well made, simple to set up, performs well and consistantly

24 KG !!! A noter si vous habitez en hauteur sans ascenceur. Je n'avais pas fait attentin au poids ! Emballé dans une caisse en bois. Premiers essais concluants, montage simple. Bonne pression. Très satisfait.

Perfect machine, heavy duty, no problems, shipped tight, nothing missing, very happy

It came quickly. It was as described. It was boxed up very well but there was damage to the box but the press was fine. There is an instruction book but it does not tell you anything about putting it together for adjusting. I had to watch a couple videos of other people with theirs to realize the cutting board was not attached with the four screws and that came with it. It works very well after I got it adjusted. I have no complaints.

14.2x10.2 Press is very solid & ridiculously heavy. Needed a press to repeatedly and consistently apply pressure in a vertical motion without side to side motion. Using with large 6”x5.5” top and bottom embossing plates for cardstock paper, if the press has any sideways movement, the plates would not line up and would become damaged . Needed to build a jig out of mdf for my purposes but the press performs the intended task incredibly well. There are only 3 minor issues that are probably not an issue for most users. First issue is that it weighs a little over 100 pounds. As such, you need a dedicated space to place it as it’s much too heavy to store away and bring out repeatedly. Second issue is that there’s very little vertical travel (approximately 5mm total) when you pull the lever to operate the press. For leather dies, where you have room to get your hand between the plates, to line things up, the vertical travel is likely just fine. I’m not using this for leather and a little more vertical travel would be a huge benefit. Third issue, the cardstock I’m working with requires the larger press in order to fit the paper between the 2 upright threaded posts. The upper press plate is very large at 10.2” wide and lining up the paper precisely is very difficult as a result. It would be nice if Vevor offered an optional plate that was maybe 6” wide. If there were more travel between the plates, that would solve the problem as well. Again, these are likely not issues for most users. This is marketed as an embossing press and sometimes embossing plates are a top and bottom plate, not just a top plate. The press works beautifully but you’ll need to get a little creative building a jig if you’re using this for top and bottom plate embossing. The press is very well built, all parts are solid and it will likely outlast me. For the price, it’s an absolute bargain. Some reviews mention the instructions are quite vague. There were no instructions in the crate when I unpacked it, so I can’t comment on how vague they are! I’m not sure why anyone would really need instructions though, it’s pretty straight forward. Undo the retaining nuts, level the plates, tighten the retaining nuts and use the press. It really couldn’t be more simple.