Reseñas de clientes para Motor eléctrico VEVOR de 1 HP, 1725 rpm, CA 115 V/230 V, chasis 56C, motor compresor de aire monofásico, eje con chaveta de 5/8", rotación en sentido horario/antihorario para maquinaria agrícola y equipos generales.
1725 RPM 1,0 HP
Opiniones de los Clientes
Cómo funcionan las reseñas y calificaciones de los clientes
Las reseñas de los clientes, incluidas las calificaciones con estrellas de los productos, ayudan a los clientes a obtener más información sobre el producto y a decidir si es el producto adecuado para ellos.
Nuestra calificación general no es un simple promedio. Priorizamos las reseñas auténticas y confiables, y filtramos los duplicados o el contenido inválido antes de calcular la puntuación final. Esto garantiza que la calificación refleje fielmente las experiencias reales de los clientes.
Reseña este producto
Comparte tu opinión con otros clientes.
Escribe una reseña
133 Reseñas
Reseñas del Artículo Actual
Compra verificada
Solo fotos y videos
Traducir todas las reseñas a Español
Eric Deziel Company owner
1725 RPM 2,0 HP
Purchased the motor to replace the motor on a SouthBend lathe
Works great and very quite
Would by it again
0 personas encontraron esto útil
Traducir reseña a Español
Patrick Owner
2.0HP
Works well, I did wire it 220v due to current draw. Meets expectations and works well as a replacement on belt sander.
1 personas encontraron esto útil
Traducir reseña a Español
Gene Engineer
1725 RPM 2,0 HP
Replace an old 1.5HP compressor motor with the 2HP electric motor 1725 RPM running with 230v, worked as it should (had to change to run Clockwise vice CCW as it came running CCW. Wiring was easy to understand (if you are use to working with motor wiring). Seems heavy duty, quiet and smooth. Started the old 2 stage compressor with no issues. Would recommend.
0 personas encontraron esto útil
Traducir reseña a Español
AC 220V motor
2.0HP
Working very well on my car lift. The motor was very simple to install I would definitely recommend this motor for projects around the house.
1 personas encontraron esto útil
Traducir reseña a Español
Michael Donnelly Used on 14" Harbor Freight Bandsaw
1725 RPM 1.5 HP
This motor being rated at twice what the saw came with has worked perfectly. I wired it to run on 240v to keep the current draw lower. The instructions for wiring 120v or 240v and reversing directions are fairly straightforward. This motor having a thermal overload is a big plus. The bolt pattern and shaft size were the same as the 0.75hp motor that I burnt up within a few hours of first running the saw. This motor was a bit larger and required a bit of modification to the enclosure for it to fit, but it has been a great upgrade. I would recommend this motor and will buy again from Vevor as long as they continue to keep their prices right.
0 personas encontraron esto útil
Traducir reseña a Español
Mark good motor
0.75HP
The motor runs good, but the only thing I am concerned with is that it seems to run hot to the touch. But I have not put a temperature reader on it to actually check it. Also the knock-outs on the wiring box wouldn't 'knock out'.
0 personas encontraron esto útil
Traducir reseña a Español
Marc Sir
0.75HP
Seems good. The junction box tabs are fully welded and don't pop out for access. I had to drill a hole.
0 personas encontraron esto útil
Traducir reseña a Español
Karen Ryan Performance
1725 RPM 1.5 HP
Works good
0 personas encontraron esto útil
djg125 Works
3450 RPM 1,0 HP
Works for intended purpose
0 personas encontraron esto útil
B.E. Great motor
1725 RPM 1.5 HP
Overall this motor has been great. I’m happy with putting this on my bandsaw. I doubled the hp and it’s cutting aluminum and some steel great.
The only issue I have was the knock out. I could not get them to come out and bent up the pecker head.
0 personas encontraron esto útil
Traducir reseña a Español
