Reseñas de clientes para VEVOR - Juego de 2 patas de acero para mesa de comedor (71,1 cm de alto y 76,2 cm de ancho), resistentes, con sección cuadrada de 8 cm y marco en X, 71,1 cm x 76,2 cm x 8 cm, color negro, estilo industrial rústico.

Très bon achat, le plateau de table étant très lours j'avais besoin de pieds adéquats, la table est longue on aurait eu besoin d'un troisième pied que je n'ai pas trouvé à l'unité sur ce site, alors on a mis un tréteau solide. La table est valorisée grâce à ces deux pieds: de la classe tout en gardant un côté rustique, campagnard. Je recommande cette marque et ce produit.

I read a lot of comments about table wobble with these legs. In light of these comments I decided to add a hole as close as I could to the ends opposite to the holes available on the flange. I used 1 inch lag bolts with big washers. There was no wobble this way with a 42/84 inch walnut table that was 1 1/4 thick and had 3 1/2 inch sides. Not user firendly but you can get these legs to work fine.

Nicely welded legs. No screws or assembly needed. Metal quality is not top but seems quite good. Adjustable feets

Pieds très robustes, Les vis d’ajustement rendent néanmoins le table un peu branlantes. En les retirant et en posant directement sur les surfaces d’appui des X on supprime le problème. Très satisfait de mon achat!

The legs look great and were uniform. The legs once screwed to the table tended to wobble (about 46 inches apart), as other reviewers stated. The top plate should be wider with more screw holes on both sides would help with stability. I drilled these my self. I also installed 2" steel angle iron between the legs, attaching it inside the top V by drilling two sets of holes in each leg (one in the V and one on either flat - total of 3), on set on out edge of V and other on inside edge, for a total of 6 holes in the angle iron and each leg). I used self-tapping #14 screws, I pre-painted everything black. Came out nice and the table was rock solid.

The table legs are nice looking, great quality and good finish. I custom made a quartz table top for the table legs and used 3/4” plywood to fit inside underneath the table. I also added cross bar pieces of plywood to help support the table from shaking. It’s a lot better now but still shakes a bit. I have 2 suggestions (1) the seams in the table legs need to look seamless as I can see the welding joints at the X (2) the table is unstable even with extra supports (I have quite a bit of supports so it’s now okay but still shakes a bit). I suggest a cross bar at the joining of the X for proper support or at minimum provide the option to buy the support.

It arrived with a few scratches, not well enough packaged, only one layercardboard as protection. Top plate little thin, one mm thicker would have been better. Otherwise nice.

Befestigung funktioniert nur mit "Schrauben um die Ecke", da die Löcher teilweise ungünstig vorgebohrt wurden. Ließ sich für uns leider nicht umsetzen.

Pieds de bonne qualité, correspondent bien à la description du produit. Supportent très bien un plateau de table en chêne massif assez lourd. Deux points pourraient être améliorés : - les vis fournies sont un peu trop petites - les platines de fixation sont sous-dimensionnees : 2 ou 3 cm de plus en largeur aideraient pour la mise en place des vis

Beine stark verkratzt und eingedelt, Schraublaschen fehlen jeweils an einer Ecke, so dass die Beine angeschraubt wackeln. Lieferung war schnell