Reseñas de clientes para VEVOR Tanque de presión para pintura en aerosol, 30 L/8 galones, con agitador manual, sellador de fugas para la industria, decoración del hogar, arquitectura, construcción, pintura automotriz, 70 PSI máx.

Works great as a pressure pot for resin. You’ll need knowledge and a bolt and two rubber washers to convert it but those are ready available. It’s worked great so far. I need to make shelves for it. I’ll use magnets for supports.

Works well for resin casting. The paint and weld quality looks good. No complaints.

I started with a press. pot from HF and quickly outgrew it. This pot is the ideal size for home casting. With minor tweaks it fits the bill wonderfully, held pressure for 48 hours loosing only 2 psi. I will be using this pot for years to come.

Got this pot for resins, I have done two bowls with in no issue, quality great, easy to use. Had to take out paint feeder pipe but this was easy. How I removed the pipe:- Removed filter from bottom of pipe and cut a slot in thread with a metal saw at bottom and removed it with a large screwdriver or you can also put 2 bolts on and locked them tight together and then twisted it off. I also changed the intake valve to a car tyre vale (see image) got the part from https://www.thorite.co.uk as I don’t have an air compressor. I use a makita battery tyre pump but have done it with a foot pump and a bicycle pump, takes 2 mins with a cycle pump to get it up to 50 psi.

Compre una camara de presurizado el domingo y hoy a dia martes ya la tengo en casa! Increíble precio por su gran calidad y sobre todo rapido! Todo PERFECTO no soy un BO0T👍🏼👍🏼🔥

Jag är skulptör. Jag skapar skulpturer i lera, skapar sedan en silikonform, tar sedan bort leran från formen och fyller håligheten med polyuretanharts (d.v.s. hartsgjutning). Jag använder tryckkärlet för att minska förekomsten av bubblor under gjutningsprocessen. Det fungerar som en dröm. Inga klagomål.

De lucht regeling op het spuitpistool was defect. Met beetje loctite was dit snel terug in orde. Gebruikt om 25m tuin platen te spuiten met hars op waterbasis. Is goed gelukt. Blij met de aankoop van Vevor

L ho usata molto comoda per grandi pareti ha bisogno di un buon compressore io sono molto soddisfatto la consiglio a tutti quelli che devono verniciare grandi superfici !

Ich verwende den Behälter als Druckkammer für Epoxid-Harz Projekte. Hierbei ist es notwendig, die Objekte unter ca. 4 Bar über einen Zeitraum von 4 Tagen zu halten. Am Behälter habe ich dazu folgende Anpassungen vorgenommen: Den Rührstab habe ich ausgebaut und das entstandene Loch mit einem M18 Gewindestab, Unterlegscheiben und 2 Muttern geschlossen (das Gewinde etwas mit Silikon abgedichtet). Den Ansaugstutzen habe ich abgeflext. Anfangs hat der Behälterdeckel nicht richtig abgedichtet, obwohl ich die Flügelmuttern fest angezogen hatte. Nach dem 'einfetten' der Schraubengewinde konnte man diese noch etwas fester anziehen, so dass der Druck gehalten wurde bzw. nur noch minimal nachgelassen hatte. Der Support von VEVOR hat hierbei gut geholfen. Normale Druckluftleitungen passen an dem Eingangsventil. Die Ventilhebel sind zwar etwas dünn, die Funktion ist aber gegeben. Wer das Manometer direkt hinter die Flügelmutter positioniert hat, erschließt sich mir nicht. Alles in allen keine Profiqualität, aber für den ambitionierten Hobbyisten durchaus gut geeignet. Würde ich den Behälter wieder kaufen: Ja

I ordered the smaller 10l pressure pot from Vevor. It seems designed for resin casting but still has a paint pipe installed in case you want to spray paint. This gets in the way of casting. I think Vevor should remove it. I did - with an angle grinder. I couldn't unscrew it. The pot works fine up to 50 psi (which is high as I need to go). No bubbles in the resin. No leaks from any point on the pot either, so no need for the supplied sealant. For £114, this pressure pot is way cheaper than the competition. I didn't find any CE quality marks and I haven't tested the safety pressure release (60psi) but it works well. If Vevor supplied castors the price would be a little higher, but I think they could remove the paint pipe (as an option?) or blank off that fitting without a major cost and sell it for the purpose most purchasers will use it for - resin casting. It would be good if they supplied an adjustable caddy as well as the internal base plate. Overall however, I'm very satisfied.