Reseñas de clientes para Extractor de miel eléctrico VEVOR, centrifugadora de miel de 4/8 cuadros, acero inoxidable, con soporte de altura ajustable y tapa.

Για τα λεφτά του πολύ καλό. Θα προτιμούσα να είχε ποιο σταθερά πόδια και καλύτερες θέσεις για τα πλέσια.

Neat and tidy once you get set up. It is tricky to clean up and replace the spindle in the correct position so you don't scrub out the rubber stoppers but once you know it is ok. No different to another of these i have used. So this one is great for the price.

Prima honing slinger apparaat, doet wat het moet doen en dat voor een lage prijs. ik heb de honing slinger niet vast ergens op gemonteerd tijdens het gebruik en daarom onder de poten trilling rubbers gemonteerd. ik adviseer om alle reeds gemonteerde schroefjes en boutjes te controleren of ze goed vast zitten ,anders trillen ze waarschijnlijk los. prima product voor de kleine imker.

Works great. Wobbles if you don't brace the legs. A simple 2x4 T plate reduced the wobble a lot. Other than the drain being to high up it is a good unit overall. Would buy again!

Funziona bene nei limiti dei 2 telaini da melario + 2 telai da nido come capacità max. e quindi ci vuole pazienza, per uso hobbistico fino a 4-5 famiglie va bene. Ho aggiunto un triangolo in legno che collega i 3 piedini e aiuta la stabilità. Prezzo e qualità buona, solo il rubinetto non ha una tenuta perfetta e gocciola un po', ma si può sistemare.

Franchement à ce prix là, faut pas se priver... les pieds sont toutefois fragiles (peut être qu'avec un quatrième pied il eut été plus stable) et je n'ai pas trouvé la solution idéale pour stabiliser correctement l'engin en vitesse de croisière. La partie moteur peut se désolidariser de la cuve pour le nettoyage, ça c'est top, dommage que le mode d'emploi n'en parle pas pour montrer comment on procède.

je recommande ce produit. arrivé très bien emballé et dans les délais. utilisé pour extraction de miel, petit bémol : cet extracteur n accepte pas pas les cadres type Hoffman pour quelques minimètres, pas de soucis avec les cadres droits. pas de possibilité d inverser le centre de rotation. la vitesse de rotation pas assez rapide à mon sens mais j ai compensé en augmentant la durée de rotation. qualité prix

Good value for money, the stands are a bit week and could be a bit taller to accommodate a bigger bucket.

Sehr gutes Preis-/ Leistungsverhältnis. Qualität gut, Kanten teilweise etwas scharf. Kleiner Minuspunkt ist der relativ hohe Auslass. Geht mit Kippen auch, aber halt mühsamer. Trotzdem absolut zu empfehlen

I've been waiting to do this review as I wanted to have used it a couple times first. I bought this extractor in Feb '24 and have used it 3 times. I was slightly concerned with some of the more negative comments, however, with that in mind decided to give this machine a try. Firstly, I am a hobbyist beekeeper and only do extractions about 2-3 times per year depending on flow. I have used the machine 3 times since Feb and extracted around 30+ frames of honey. The extractor is easy to use and does a very good job. The legs are a bit light and can cause more wobble than necessary, but I bolted the bases of the legs (they have holes cut out for this purpose) to a triangle of plywood and that firmed everything up. I attached locking castors to the bottom to easily move it around my shed. Also, you need to use your head a bit and think about using frames that feel close in weight to minimize the wobble at the start of extraction. If that isn't possible, go slow until the frames gradually become equal as the honey gets extracted, then speed up further. It is a bit of a "feel" thing, hard to explain, but easy to experience. The comments on having the honey gate too high are accurate, but with the legs locked into the plywood base you can easily tip the machine a bit to get the last of the honey out. But, this would be a good design improvement, if they made the honey gate lower. The motor is smooth and and works well. It did a great job of extracting the honey and supporting the frames during the process. It's all stainless steel and easy to clean. I take off the motor and pull out the baskets to clean everything after the extraction and it is quite simple to do (once you've done it for the first time). Beware, there is a ball bearing in the bottom center cup that the basket rod fits into, so if you turn the extractor over completely to get out any last water, that bearing can/will fall out. Just plunk it back in, reassemble and you're good to go. I also bought some food grade grease for the bearing maintenance. Overall, I am super happy with the extractor and it fits well for hobbyists.