Reseñas de clientes para Motor eléctrico VEVOR de 2 HP, 1725 rpm, CA 115 V/230 V, chasis de 143/5 T, compresor de aire monofásico, eje de chaveta de 7/8", rotación en sentido horario/antihorario para maquinaria agrícola y equipos generales.
1725 RPM 2,0 HP
Opiniones de los Clientes
Cómo funcionan las reseñas y calificaciones de los clientes
Las reseñas de los clientes, incluidas las calificaciones con estrellas de los productos, ayudan a los clientes a obtener más información sobre el producto y a decidir si es el producto adecuado para ellos.
Nuestra calificación general no es un simple promedio. Priorizamos las reseñas auténticas y confiables, y filtramos los duplicados o el contenido inválido antes de calcular la puntuación final. Esto garantiza que la calificación refleje fielmente las experiencias reales de los clientes.
Reseña este producto
Comparte tu opinión con otros clientes.
Escribe una reseña
134 Reseñas
Reseñas del Artículo Actual
Compra verificada
Solo fotos y videos
Traducir todas las reseñas a Español
Gervais Picard 1hp motor
1725 RPM 1,0 HP
Motor for my planer works great and running so smoothly, i will purchase another one for my other tools if i need to. Good quality and easy to plug.
0 personas encontraron esto útil
Traducir reseña a Español
Jhubb Motor Review
3450 RPM 1.5 HP
Perfect fit for a Craftsman Table Saw 317 series. Plenty of power quite and well balanced. good replacement motor price was good
0 personas encontraron esto útil
Traducir reseña a Español
Patrick Owner
2.0HP
Works well, I did wire it 220v due to current draw. Meets expectations and works well as a replacement on belt sander.
1 personas encontraron esto útil
Traducir reseña a Español
AC 220V motor
2.0HP
Working very well on my car lift. The motor was very simple to install I would definitely recommend this motor for projects around the house.
1 personas encontraron esto útil
Traducir reseña a Español
Michael Donnelly Used on 14" Harbor Freight Bandsaw
1725 RPM 1.5 HP
This motor being rated at twice what the saw came with has worked perfectly. I wired it to run on 240v to keep the current draw lower. The instructions for wiring 120v or 240v and reversing directions are fairly straightforward. This motor having a thermal overload is a big plus. The bolt pattern and shaft size were the same as the 0.75hp motor that I burnt up within a few hours of first running the saw. This motor was a bit larger and required a bit of modification to the enclosure for it to fit, but it has been a great upgrade. I would recommend this motor and will buy again from Vevor as long as they continue to keep their prices right.
0 personas encontraron esto útil
Traducir reseña a Español
Robert Mr.
1725 RPM 1,0 HP
Just what I needed to replace the factory 1hp motor on my Central Pneumatics 16 speed floor drill press.
It is a little bit bigger and heavier than the original motor but it works great.👍🏻
0 personas encontraron esto útil
Traducir reseña a Español
David Welborn Great motor but junction box punch outs wouldn’t punch out
3450 RPM 1.5 HP
I would’ve given five stars except I had a little problem. The punch outs for the cable box were not deep enough, and I ended up having to drill a hole. I changed out the motor on my table saw. It’s a craftsman. It wasn’t easy, but it worked. It wasn’t easy because of the clearance of the mounting plate and the screws.
0 personas encontraron esto útil
Mark good motor
0.75HP
The motor runs good, but the only thing I am concerned with is that it seems to run hot to the touch. But I have not put a temperature reader on it to actually check it. Also the knock-outs on the wiring box wouldn't 'knock out'.
0 personas encontraron esto útil
Traducir reseña a Español
Marc Sir
0.75HP
Seems good. The junction box tabs are fully welded and don't pop out for access. I had to drill a hole.
0 personas encontraron esto útil
Traducir reseña a Español
Karen Ryan Performance
1725 RPM 1.5 HP
Works good
0 personas encontraron esto útil
